需要进入美国市场的无线产品、通讯产品和数字应用产品,必须通过由美国联邦通信委员会 FCC 授权的实验室跟据其技术标准进行的检测,并取得FCC认证证书。FCC全称是Federal Communications Commission,中文为美国联邦通信委员会。于1934年根据Communications Act建立,是美国政府的一个独立机构,直接对国会负责。FCC通过控制无线电广播、电视、电信、卫星和电缆来协调国内和国际的通信。涉及美国50多个州、哥伦比亚以及美国所属地区为确保与生命财产有关的无线电和有线通信产品的安全性,FCC的工程技术部(Office of Engineering and Technology)负责委员会的技术支持,同时负责设备认可方面的事务。
认证范围涉及个人电脑及周边、无线产品、音视频产品、家用电器、玩具、灯具、电动工具、安防产品、工业机械等产品。
产品及包装上(或说明书)都需要FCC及IC标识,分别要求如下:
1、带无线遥控的产品上的标识:
A 发射产品上: ID XXXXXXXX.可以用贴纸或丝印等方式
B 接收部分的标识如下(30MHz以下的接收器不用加贴--参考FCC15.101):
Trade Name:(品名或公司名)
Module No. (产品型号)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including interference that may cause undesired operation.
C 包装或说明书(或吊卡)上的标识:
WARNING: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
2、普通电子产品:
A 产品上的标识(与带无线遥控产品标识比较,少了产品编号及公司名称):
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
B 包装或说明书(或吊卡)上的标识:同带无线遥控产品的包装上标识
FCC针对电子产品的类型分为两种不同的认证方式,分别为:FCC SDoC和 FCC ID(Certification) ,前者适用于普通不带无线功能产品,后者适用带无线功能的产品。
FCC SDoC | FCC ID | |
适用产品 | 普通不带无线功能产品,如显示屏、灯具等 | 带无线功能产品,如手机、蓝牙耳机等 |
测试内容 | 电磁兼容EMC | 电磁兼容+射频RF |
认证费用 | 低 | 高 |
测试周期 | 时间短 | 时间长 |
1、客户提交申请表给检测机构;
2、客户准备检测样品(无线产品需要定频机),并提供产品资料(见资料要求);
3、检测机构出具草稿报告,客户确认,签发正式报告;
4、如果是FCC sDoC,则项目完成;如果是申请FCC ID,提交报告及技术资料给TCB;
5、TCB审核完成签发FCC ID证书,检测机构发送正式报告、FCC ID证书;
6、企业获得FCC认证后,即可在产品上使用FCC标志及相关的Statement;
注:首次申请FCC ID认证的厂商,需要在FCC注册FCC-FRN建立申请公司档案,在TCB审核完成后签发的证书会有FCC ID号码,通常FCC ID是由”厂家代码 (Grantee code)”+ ”产品代码(Product code)”组成。
厂家代码:为三位的数字或大写字母,由FCC直接发放;
产品代码:为数字、字母、”-”组成,但其中不能有连续两个或两个以上的”-”使用,首位和末位也不能使用”-”,此代码位数最长不超过14位,该号码客户可以自定。
1、使用说明书 User manual
2、方框图 Block Diagram
3、电路原理描述 Operation Description
4、电路原理图 Circuit schematic
5、RF调制方式 RF modulation
6、宣告的额定功率 Rated Power Declaration
7、申请表 TCB Form 731
8、授权信 POA
9、FCC保密信
注:FCC ID认证需要提交资料清单和要求如下:
(1)FCC申请表:申请公司名称、位址、连络人信息、产品名称和型号、使用标准等信息要求准确无误;
(2)FCC授权信:要由申请公司的连络人签名盖章并扫描成电子档;
(3)FCC保密信:保密信是申请公司与TCB机构签订的对产品资料保密的协定,要由申请公司的连络人签名盖章并扫描成电子档;
(4)方框图:需要画出所有晶振,以及晶振频率,并与电路图保持一致;
(5)电路图:必须要和方框图里面的晶振频率、晶振数量及晶振位置一致;
(6)线路描述:要求为英文,把产品的功能实现原理描述清楚;
(7)使用说明书:要求有FCC Statement;
(8)标签和标签位置:标签要有FCC ID号码和Statement,标签的位置要求显著;
(9)产品内外观照片:要求图片清晰明了,必要时增加备注;
(10)测试报告:要求测试完成,根据标准条款全方位评估产品;
按照 47 CFR 相关标准进行测试,测试项目包括:
辐射发射
传导发射
谐波电流
谐波闪烁
频率误差
邻频道功率
杂散发射
传导载波功率
有效发射功率
发射器对调制频率的响度
宽带设备的调制带度的范围
低电压条件下频率稳定度
1、Certification的测试必须在FCC认可的实验室进行。
2、选择Certification认证程序的产品,E-label是可被接受的。
3、SDoC的责任方必须是美国注册的实体。
4、SDoC适用范围内的产品,也可以选择使用认证程序; 但认证管控范围的产品,只能选择认证程序。